IKEA spare parts compatible with PAX wardrobes: the guide for all repairs

A move, an open bag of screws, and a single missing part. Your PAX wardrobe leans and nothing aligns. This is a common problem. Here is how to identify and replace your IKEA spare parts compatible with PAX wardrobes to get your dressing room squared away.

What dimensions for your IKEA spare parts compatible with PAX wardrobes?

The PAX system relies on three critical measurements. An accessory for a 35 cm frame will never fit into a 58 cm model. This is the most frequent purchasing error.

Dimension	Variants	Point of attention
Width	50, 75, 100 cm	Not interchangeable
Depth	35 or 58 cm	Specific accessories
Height	201 or 236 cm	Affects the doors

Always check the Width × Depth combination before ordering.

Why is my door sagging?

The door no longer closes or rubs against the frame. The problem often stems from spring wear or loose screws. The hinge has developed play under the weight of the panel.

First, adjust the depth screws. If the metal is bent, replace the part. Use a KOMPLEMENT hinge (1013380) for perfect alignment. Tighten the screws with a Pozidriv PZ2 screwdriver to avoid stripping the head.

My drawers are sticking, what is the solution?

A drawer that jams or comes off its rail is often the result of overloading. The metal rail bends under the weight. If the end stop is broken, the drawer hits the back.

Replace the KOMPLEMENT drawer slide (1013376). Ensure the fixing screw is perfectly flush. A protruding screw head can cause the bearing to jump. For maintenance, use a dry Teflon lubricant. Avoid WD-40, which attracts dust.

My shelves are tilting, why?

The shelf leans because a support pin has popped out or broken. These small parts (reference 110338) are easily lost.

Check the four corners of your shelf. If the hole in the wood is too wide, the pin no longer holds. Fill the gap with a toothpick and wood glue before repositioning the part.

Why is my drawer bottom sagging?

The bottom forms a "V" and is at risk of failing. The plastic fasteners have given way under pressure. The KOMPLEMENT bottom panel (1013378) must be replaced.

Do not attempt to glue it back; glue does not hold on this fiber. To prevent this from happening again, place heavy objects on the sides, near the walls, to relieve the center.

My door slams too hard, what should I do?

The closing noise is violent and marks the frame. Your rubber buffers are worn or detached.

Glue new door bumpers (100344) to the four corners. This protects the wood and eliminates the slamming.

Old generation and new: is everything compatible?

IKEA has maintained stable dimensions for 20 years. Compatibility is therefore generally good. The hinges use the standard European 35 mm drilling. You can install recent hinges on an old frame.

Be careful with sliding doors: some rails have evolved. Double-check the height of your frames (201 or 236 cm). KOMPLEMENT accessories remain compatible with all versions.

How to move your PAX without breaking everything?

Moving an assembled frame is risky. The weight of the particle board weakens the fasteners and the furniture can warp. Disassembly is essential.

Empty the interior, remove the drawers, and take off the doors. Unlock the cam locks with a flat-head screwdriver. Remove the nails from the back panel with pliers. If you tear the panel, you lose structural stability.

Store each screw in a labeled bag ("Left Frame", "Right Door").

Pro tips for indestructible furniture

An uneven floor creates tension in the wood. Use rigid plastic shims under the base, never cardboard.

Check the squareness before nailing the back. Measure the two diagonals of the frame: they must be identical to the millimeter. Nail the back every 10 cm to avoid the "parallelogram" effect.

It is imperative to fix the furniture to the wall using metal expansion anchors (Molly type) for drywall. Plastic anchors cannot support the weight of a loaded PAX.

If a screw hole is stripped, fill it with matchsticks and wood glue. Let it dry, cut the excess, and screw back in.

Find all precise references and assembly instructions just below.